- LSM6DSO(3-Axis Accel + 3-Axis Gyro), LIS2DML(3-Axis Mag), LPS22HH(260-1260 Absolute Pressure Sensor
- Ultra Small 15.2 x 12.7mm
- Configurable between I2C and SPI interfaces without having to remove resistors!!
- Default = SPI to LSM6DSO
- All sensors can be controlled via single LSM6DSO interface
- smWSP-ARD, smWSP Compatible(Wireless Sensor Rapid Protyping Kits)
-
smMOT-10DOF-ST : 10 DOF IMU Breakout Board with I2C and SPI Interfaces -
The PAM8904 is a 1X/2X/3X Piezo Driver capabable of 1X/2X/3X Boost modes with an input of 1.8-5.5V. The smPWR-PAM8904 provides a micro-sized breakout board measuring 20.4x12.7mm for the PAM8904 and provides jumper pin selections for the 1X/2X/3X modes and oversized solder pads for connecting a piezo speaker/buzzer. Additionally the device has excellent built in features such as Automatic Standby Operation and Wake-Up-Control. -
3 PIECE MINIMUM ORDER ORDERS $20 OR MORE PROVIDES FREE SHIPPING IN CONTINENTAL USA INQUIRE FOR VOLUME ORDERS OR OTHER BATTERY SIZES/CAPACITIES!! The smLiPo-605048 Lithium Polymer battery is a high capacity/high discharge rate rechargeable battery that is well suited for IoT application such as LTE-M or WiFi or even lower power products that want to have a long duration in between charges. The smLiPo-604045 is still small enough to fit into small embedded applications. It comes standard with a commonly used JST PHR-2 connector. The smLiPo-605045 is also fully protected with built in Over-Voltage(OV) and Under-Voltage(UV) protection to protect against over-charging and over-discharge events.- 1600mAh Capacity
- 3.7V nomimal voltage
- Standard Lithium Battery Charge voltages and discharge cutoff voltage
- Connector wired to battery: JST PHR-2
- Mating Connectors for PCB:
- B2B-PH-K-S -> Top Entry Thru-Hole
- S2B-PH-K-S -> Side Entry Thru-Hole
- B2B-PH-SM4-TB -> SMT Top Entry
- S2B-PH-SM4-TB -> SMT Side Entry
-
This is a MP2148 Low Iq DC-DC Buck regulator breakout board. The Monolithic Power MP2148 is a DC/DC buck regulator capable of 1A continuous output current from a 2.3V-to-5.5V input voltage with excellent load and line regulation. All of this is achieved at a mere 11uA of quiescent current. Fault protections include cycle-by-cycle current limiting and thermal shutdown. The MP2148 is available in an ultra-small QFN- 6 (1.0mmx1.5mm) package and requires a low value inductor of only 1uH and can provide >90% efficiency. The smPWR-MP2148-ADJ provides an easy to use breakout board for the MP2148 measuring only 7.8x9.9mm. All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread-board or to be ‘wired’ into an application. The header-header spacing is 7.62mm (300mil). The smPWR-MP2148-ADJ comes pre-configured for a 3.0V output but can be modified to provide a 1.8V output by simply moving R3(0603) 0ohm jumper. By default the EN line is pulled to Vin via R1(0ohm jumper). For external control for Enable/Disable simply remove R1. All SMSTRS smMEM, smSENSR, smCOM, smBAT, smPWR products are compatible with the Sensor Maestros Wireless Sensor Platforms that provide Rapid prototyping for Sensor and BTLE applications. The smPWR-MP2148-ADJ can be plugged into ANY of the smPWR sockets in the smRF-WB and smWSP-ARD rapid prototyping sensor plugin boards. smWSP-ARD: Arduino compatible IoT Sensor Rapid Prototyping Platform MP2148 Datasheet For orders over 100 fill out this form -
The AT25XE041A is one of the world’s lowest power Serial Flash Device. It boasts 200nA Ultra Deep Power Down currents. The device operates from 1.65V-3.6V and up to 85MHz. the AT25XE041A has a flexible erase architecture and can be erased in 4,32,64Kbyte blocks or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT25XE041A offers several package options including an ultra-small 2x3x0.6mm UTDFN package of which the smMEM-AT25XE041A breakout board makes use of. For orders over 100 fill out this form. -
The AT25XE021A is one of the world’s lowest power Serial Flash Device. It boasts 200nA Ultra Deep Power Down currents. The device operates from 1.65V-3.6V and up to 85MHz. the AT25XE021A has a flexible erase architecture and can be erased in 4,32,64Kbyte blocks or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT25XE021A offers several package options including an ultra-small 2x3x0.6mm UTDFN package of which the smMEM-AT25XE021 breakout board makes use of. The smMEM-AT25XE021 provides an easy to use, low-cost, very small breakout board for the AT25XE021A. All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread-board or to be ‘wired’ into an application. The header-header spacing is 10.2mm (400mil). All SMSTRS smMEM, smSENSR, smCOM, smBAT, smPWR products are compatible with the Sensor Maestros Wireless Sensor Platforms that provide Rapid prototyping for Sensor and BTLE applications. The smMEM-AT25XE021 can be plugged into ANY of the smBLOCK SPI sockets in the smWSP and smWSP-ARD rapid prototyping plugin boards. For orders over 100 fill out this form.
