-
The AT45DB641E is a low voltage, low power Serial Flash Device. It boasts 400nA Ultra Deep Power Down currents. The device operates from 1.7V-3.6V and up to 85MHz with a Low Power Read at 15MHz. The AT45DB641E has a flexible erase architecture and can be erased by Page(256bytes), Block(2KB), Sector(64KB), or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT45DB641E offers several package options including 8ld SOIC(0.208” wide), 9-Ball BGA(6x6mm) and an 8ld UDFN(5x6x0.6mm) package of which the smMEM-AT45DB641 breakout board makes use of. For orders over 100 fill out this form. -
This is a MP2148 Low Iq DC-DC Buck regulator breakout board. The Monolithic Power MP2148 is a DC/DC buck regulator capable of 1A continuous output current from a 2.3V-to-5.5V input voltage with excellent load and line regulation. All of this is achieved at a mere 11uA of quiescent current. Fault protections include cycle-by-cycle current limiting and thermal shutdown. The MP2148 is available in an ultra-small QFN- 6 (1.0mmx1.5mm) package and requires a low value inductor of only 1uH and can provide >90% efficiency. The smPWR-MP2148-ADJ provides an easy to use breakout board for the MP2148 measuring only 7.8x9.9mm. All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread-board or to be ‘wired’ into an application. The header-header spacing is 7.62mm (300mil). The smPWR-MP2148-ADJ comes pre-configured for a 3.0V output but can be modified to provide a 1.8V output by simply moving R3(0603) 0ohm jumper. By default the EN line is pulled to Vin via R1(0ohm jumper). For external control for Enable/Disable simply remove R1. All SMSTRS smMEM, smSENSR, smCOM, smBAT, smPWR products are compatible with the Sensor Maestros Wireless Sensor Platforms that provide Rapid prototyping for Sensor and BTLE applications. The smPWR-MP2148-ADJ can be plugged into ANY of the smPWR sockets in the smRF-WB and smWSP-ARD rapid prototyping sensor plugin boards. smWSP-ARD: Arduino compatible IoT Sensor Rapid Prototyping Platform MP2148 Datasheet For orders over 100 fill out this form -
The ICS-43434 is a digital I2S output microphone featuring a bottom sound port. The ICS-43434 provides a direct Audio to Digital solution. No Audio Codec is needed to get direct sampled audio straight to a host processor. The ICS-43434 follows the industry standard 24-bit I2S interface for easy connection to any host processor that has an I2S interface. It provides 3 operation modes: High Performance(~490uA), Low Power(230uA) and Sleep(~12uA) while being powered from a 1.8V source. In a very small package size of 3.5x2.65x0.98mm it also provides a high SNR of 64dBA across a 20KHz bandwidth along with an exceptional Dynamic Range of 90dB. For orders over 35 fill out this form. -
smMOTN-BMI160 : 6-DOF 6-AXIS BMI160 Breakout- 12.6 x 12.6mm
- I2C or SPI Configurable (Default I2C)
- All BMI160 Pins Mapped Out
- Secondary I2C Master and OIS Slave Ports accessible through Vias 1-4
- Compatible with Sensor Maestros Rapid Development IoT Platforms
- smWSP-ARD => Arduino Compatible Shield
- smWSP => Compatible with Silicon Labs EFM32 and EFR32 Starter Kits
-
smMOT-10DOF-ST : 10 DOF IMU Breakout Board with I2C and SPI Interfaces- LSM6DSO(3-Axis Accel + 3-Axis Gyro), LIS2DML(3-Axis Mag), LPS22HH(260-1260 Absolute Pressure Sensor
- Ultra Small 15.2 x 12.7mm
- Configurable between I2C and SPI interfaces without having to remove resistors!!
- Default = SPI to LSM6DSO
- All sensors can be controlled via single LSM6DSO interface
- smWSP-ARD, smWSP Compatible(Wireless Sensor Rapid Protyping Kits)
-
SPRING 2024 SUNRISE CO2 SENSOR SALE!! The SenseAir Sunrise is one of the world's lowest power and fully calibrated direct measurement CO2. As a matter of fact the Sunrise has as low as 45uA average current enabling it to be used in battery operated systems. On top of that it comes fully calibrated and provides for an automated re-calibration that has a user defined interval. Another key point is the Sunrise also has both a UART and I2C interface providing for a simple hardware and firmware interface. FREE SHIPPING FOR USA!! LOW COST INTERNATIONAL SHIPPING!! Check out the Sensor Maestros IAQ-LOGR Indoor Air Quality Reference Design!! IAQ-LOGR Product Brief_Sunrise- CO2, Temperature, Humidity, Ambient Light Monitoring
- Ultra-Low Power Beacon Mode Operation 60uA / >5yr Battery Life with 2 AA batteries
- Configurable Beacon Transmit and Sensor Sampling Intervals
- High/Low User Configurable Alarms
- Automated Data-logging to on-board memory can be enabled
- iOS/Android Mobile App for easy configuration and real-time graphing
- Log Data to CSV file or Cloud Database
- Field Firmware Update via BLE interface
- Optional Long Range BLE Capability >1000m range
- OEM Customizable
-
Sensor Maestros is the original inventor of the Rapid Prototyping Platform. Loads of thought and planning was put into the design of the smWSP-ARD. The smWSP-ARD is a Rapid Prototyping Platform for BLE and Sensor development. The smWSP-ARD has been designed to precisely mate with the Nordic nRF52 DK and is compatible with Ardiuno Revision 3. It can be used as a shield with Arduino Revision 3 compatible boards such as the nRF52 DK or as a Stand-alone BLE Sensor development kit with the addition of the smRF-LR832 Long Range modules based on the nRF52832 that provide up to +21dBm output power. For orders over 100 fill out this form. -
The SFM2 is an ultra small form-factor 9 DOF Wearable IMU with BLE and USB2.0 interfaces. The SFM2 has options for Pressure and Temperature/Humidty sensors. The SFM2 provides ultra low drift, ultra low-power, and easy configuration. The SFM2 provides up to 833Hz Sensor Fusion output data rate. SFM2's In Stock Now!! Updated with USB-C Connector!! COMING SOON => Streaming Audio from SFM2 to the Mobile App!! INQUIRE FOR VOLUME PRICING
