-
The AT25XE021A is one of the world’s lowest power Serial Flash Device. It boasts 200nA Ultra Deep Power Down currents. The device operates from 1.65V-3.6V and up to 85MHz. the AT25XE021A has a flexible erase architecture and can be erased in 4,32,64Kbyte blocks or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT25XE021A offers several package options including an ultra-small 2x3x0.6mm UTDFN package of which the smMEM-AT25XE021 breakout board makes use of. The smMEM-AT25XE021 provides an easy to use, low-cost, very small breakout board for the AT25XE021A. All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread-board or to be ‘wired’ into an application. The header-header spacing is 10.2mm (400mil). All SMSTRS smMEM, smSENSR, smCOM, smBAT, smPWR products are compatible with the Sensor Maestros Wireless Sensor Platforms that provide Rapid prototyping for Sensor and BTLE applications. The smMEM-AT25XE021 can be plugged into ANY of the smBLOCK SPI sockets in the smWSP and smWSP-ARD rapid prototyping plugin boards. For orders over 100 fill out this form. -
The AT25XE041A is one of the world’s lowest power Serial Flash Device. It boasts 200nA Ultra Deep Power Down currents. The device operates from 1.65V-3.6V and up to 85MHz. the AT25XE041A has a flexible erase architecture and can be erased in 4,32,64Kbyte blocks or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT25XE041A offers several package options including an ultra-small 2x3x0.6mm UTDFN package of which the smMEM-AT25XE041A breakout board makes use of. For orders over 100 fill out this form.
-
The AT45DB081E is a low voltage, low power Serial Flash Device. It boasts 400nA Ultra Deep Power Down currents. The device operates from 1.7V-3.6V and up to 85MHz with a Low Power Read at 15MHz. The AT45DB081E has a flexible erase architecture and can be erased by Page(256bytes), Block(2KB), Sector(64KB), or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT45DB081E offers package options including 8ld SOIC(0.150” and 0.208” wide) and an 8ld UDFN(5x6x0.6mm) package of which the smMEM-AT45DB081 breakout board makes use of. Sensor Maestros developed Software API Library for the Adesto Technology Serial Flash IC's. The API library is a portable embedded 'C' abstraction layer that can be ported to any MCU platform and includes high level API's for everything from reading, writing, erasing, reading the device ID, etc. The API library is utilized in an Application Example using the Silicon Labs EFM32 MCU platform. This application software can be used with any of the Silicon Labs EFM32 or EFR32 Starter Kits and the smWSP(Rapid Prototyping Plugin Board). The smWSP plugs into any EFM32/EFR32 Starter Kit via the Expansion Port and allows all the Sensor Maestros smMEM, smSENSR, smMOTN, etc breakout boards to be plugged into the smBLOCKs(header blocks) on the smWSP. The EFM32 'C' demo firmware reads the smMEM device plugged into the smWSP and allow various functions to be performed such as Read, Write, Erase, etc and the power consumption can be easily measured using the Silicon Labs Energy Profiler. For orders over 100 fill out this form. -
The AT45DB641E is a low voltage, low power Serial Flash Device. It boasts 400nA Ultra Deep Power Down currents. The device operates from 1.7V-3.6V and up to 85MHz with a Low Power Read at 15MHz. The AT45DB641E has a flexible erase architecture and can be erased by Page(256bytes), Block(2KB), Sector(64KB), or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT45DB641E offers several package options including 8ld SOIC(0.208” wide), 9-Ball BGA(6x6mm) and an 8ld UDFN(5x6x0.6mm) package of which the smMEM-AT45DB641 breakout board makes use of. For orders over 100 fill out this form. -
Sensor Maestros developed the smMOTN-10 DOF-ST-LSM6DSO IMU Breakout Board to provide 9 DOF IMU capability. We also included a LPS22HH pressure sensor. Equally important we designed it to measure a mere 15.2mm x 12.7mm . The LSM6DSO utilizes a single SPI interface and directly interfaces to the LIS2MDL 3-Axis Magnetometer and LPS22HH pressure sensor. Sensor Maestros also designed this breakout board to be compatible with the smWSP-ARD and smWSP Rapid Prototyping Platforms. We developed these boards as Arduino and SiLabs EFR32 and EFM32 STK compatible.- LSM6DSO(3-Axis Accel & Gyro), LIS2DML(3-Axis Mag), LPS22HH(260-1260 Pressure Sensor)
-
This is a MP2148 Low Iq DC-DC Buck regulator breakout board. The Monolithic Power MP2148 is a DC/DC buck regulator capable of 1A continuous output current from a 2.3V-to-5.5V input voltage with excellent load and line regulation. All of this is achieved at a mere 11uA of quiescent current. Fault protections include cycle-by-cycle current limiting and thermal shutdown. The MP2148 is available in an ultra-small QFN- 6 (1.0mmx1.5mm) package and requires a low value inductor of only 1uH and can provide >90% efficiency. The smPWR-MP2148-ADJ provides an easy to use breakout board for the MP2148 measuring only 7.8x9.9mm. All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread-board or to be ‘wired’ into an application. The header-header spacing is 7.62mm (300mil). The smPWR-MP2148-ADJ comes pre-configured for a 3.0V output but can be modified to provide a 1.8V output by simply moving R3(0603) 0ohm jumper. By default the EN line is pulled to Vin via R1(0ohm jumper). For external control for Enable/Disable simply remove R1. All SMSTRS smMEM, smSENSR, smCOM, smBAT, smPWR products are compatible with the Sensor Maestros Wireless Sensor Platforms that provide Rapid prototyping for Sensor and BTLE applications. The smPWR-MP2148-ADJ can be plugged into ANY of the smPWR sockets in the smRF-WB and smWSP-ARD rapid prototyping sensor plugin boards. smWSP-ARD: Arduino compatible IoT Sensor Rapid Prototyping Platform MP2148 Datasheet For orders over 100 fill out this form -
The smSENSR-LTR303ALS light sensor is a smBLOCK form factor breakout board for the LTR-303ALS-01 Light Sensor from LiteOn. smBLOCK breakout boards can be plugged into smBLOCK locations on the Sensor Maestros smWSP-ARD and smWSP Wireless Sensor platforms. The LTR-303ALS-01 light sensor is a very cost-effective 16bit light sensor in a 2x2 6LD DFN package.- 2.4-3.6V Operation / 1.7-3.6V IO Operation
- I2C 400kbs / 16bit Resolution
- 0.01 – 64K Lux Dynamic Range(1x,2x,4x,8x,48x,96x Gain settings)
- Programmable Interrupt Pin
- 50/60Hz Rejection, IR/UV Light Immunity
- 220uA operation, 5uA Standby/SLEEP
- smBLOCK I2C Pinout allows plugin compatibility with smWSP-ARD and smWSP(Silicon Labs EFM/EFR Compatible)
- Ultra-small 10x8mm Breakout Board
- 2.54mm(0.1”) headers on 7.62mm(0.3”) spacing
- Indoor Air Quality Application: IAQ-LOGR/smWSP-ARD
-
The Silicon Labs Si7006-A20 is an I2C interface, ultra-small, Temperature and Humidity Combination IC. It is offered in a 3x3x0.75mm DFN-6 package. The Si7006-A20 provides 0-90% RH with an Accuracy of +5% (max). It is operational from 0-100% RH. The Humidity sensor is configurable from 8-12bits with conversion times from 2.6-10ms respectively. The SI7006-A20 incorporates a ‘heater’ element to aid in testing the sensor, to dry the sensor membrane, or to implement a dew-point. For orders over 100 fill out this form. -
smWSP-ARP: Wireless Sensor Rapid Prototyping Shield
The smWSP-ARD is a wireless sensor rapid prototyping shield that is Arduino R3 compatible. The smWSP-ARD supports all Sensor Maestros smMEM, smSENSR, smMOTN, smCOM, smBAT, and smPWR standardized pinout breakout boards. These breakout boards plug directly into the smWSP-ARD using smBLOCKs allowing you to rapidly prototype your wireless sensor hardware one day and completely change it the next day. Gone are the days of having to work with a sensor evaluation board that has several sensors you would love to change but they are soldered directly to the PCB. Now you can pick and choose your RF, sensor, memory, power, and battery configuration. Secondarily all these components can then be un-plugged from the smWSP-ARD to be either used in a prototype of your own, in a bread-board application, or simply be replaced by a different smBLOCK compatible component. smWSP-ARD Board Includes: smCOM(USB-UART) and the smWSP-ARD base board.IAQ-LOGR Open Source Wireless Indoor Air Quality Data Logger Application
The IAQ-LOGR is an Open-Source firmware application that implements a Wireless Indoor Air Quality Monitor and Data Logger using the smWSP-ARD base board. The IAQ-LOGR application utilizes the smSENSR, smMEM, and/or smPWR and smRF standardized plugins. The IAQ-LOGR reads and data logs CO2, Temperature, Humidity, and Ambient light using the following breakout boards listed below. Open Source IAQ-LOGR firmware Repository: IAQ-LOGR Firmware More information on the IAQ-LOGR at the following link: IAQ-LOGR Product Page Volume orders please inquire directly. -
The SenseAir Sunrise CO2 Sensor is one of the world's lowest power and fully calibrated direct measurement CO2 Sensor. As low as 45uA average current enabling it to be used in battery operated systems. The Sunrise CO2 Sensor comes fully calibrated and provides for an automated re-calibration that has a user defined interval. UART and I2C Interfaces. FREE SHIPPING FOR USA!! LOW COST INTERNATIONAL SHIPPING!! Sunrise CO2 Sensor used in the Open Source IAQ-LOGR Indoor Air Quality Reference Design. -
4 PIECE MINIMUM ORDER INQUIRE FOR VOLUME ORDERS OR OTHER BATTERY SIZES/CAPACITIES!! Sensor Maestros specializes in ultra low power product design. Inquire below for custom design services. Design Services Inquiry- 130mAh 20(W) x 31(L) x 3.3(H)mm Rechargeable Lithium Polymer Battery
- Comes with ultra-low profile JST ACHR-02V-S connector.
- OV/UV Protection Built into battery
- CE Certification Document: CE Certification Document
