- 1100mAh 34(W) x 50(L) x 6.0(H)mm Rechargeable Lithium Polymer Battery
- Molex 51021-0200 Connector
- OV/UV Protection
- <180 mOhm series resistance
- 1C Max charge/discharge current
-
3 PIECE MINIMUM ORDER ORDERS $20 OR MORE PROVIDES FREE SHIPPING IN CONTINENTAL USA INQUIRE FOR VOLUME ORDERS OR OTHER BATTERY SIZES/CAPACITIES!! -
3 PIECE MINIMUM ORDER ORDERS $20 OR MORE PROVIDES FREE SHIPPING IN CONTINENTAL USA INQUIRE FOR VOLUME ORDERS OR OTHER BATTERY SIZES/CAPACITIES!! The smLiPo-605048 Lithium Polymer battery is a high capacity/high discharge rate rechargeable battery that is well suited for IoT application such as LTE-M or WiFi or even lower power products that want to have a long duration in between charges. The smLiPo-604045 is still small enough to fit into small embedded applications. It comes standard with a commonly used JST PHR-2 connector. The smLiPo-605045 is also fully protected with built in Over-Voltage(OV) and Under-Voltage(UV) protection to protect against over-charging and over-discharge events.- 1600mAh Capacity
- 3.7V nomimal voltage
- Standard Lithium Battery Charge voltages and discharge cutoff voltage
- Connector wired to battery: JST PHR-2
- Mating Connectors for PCB:
- B2B-PH-K-S -> Top Entry Thru-Hole
- S2B-PH-K-S -> Side Entry Thru-Hole
- B2B-PH-SM4-TB -> SMT Top Entry
- S2B-PH-SM4-TB -> SMT Side Entry
-
PURCHASES OF $20 OR MORE PROVIDES FREE SHIPPING IN CONTINENTAL USA!! INQUIRE FOR VOLUME ORDERS OR OTHER BATTERY SIZES/CAPACITIES!! -
smMOT-10DOF-ST : 10 DOF IMU Breakout Board with I2C and SPI Interfaces- LSM6DSO(3-Axis Accel + 3-Axis Gyro), LIS2DML(3-Axis Mag), LPS22HH(260-1260 Absolute Pressure Sensor
- Ultra Small 15.2 x 12.7mm
- Configurable between I2C and SPI interfaces without having to remove resistors!!
- Default = SPI to LSM6DSO
- All sensors can be controlled via single LSM6DSO interface
- smWSP-ARD, smWSP Compatible(Wireless Sensor Rapid Protyping Kits)
-
smMOTN-BMI160 : 6-DOF 6-AXIS BMI160 Breakout- 12.6 x 12.6mm
- I2C or SPI Configurable (Default I2C)
- All BMI160 Pins Mapped Out
- Secondary I2C Master and OIS Slave Ports accessible through Vias 1-4
- Compatible with Sensor Maestros Rapid Development IoT Platforms
- smWSP-ARD => Arduino Compatible Shield
- smWSP => Compatible with Silicon Labs EFM32 and EFR32 Starter Kits
-
The SFM2 is an ultra small form-factor 9 DOF Wearable IMU with BLE and USB2.0 interfaces. The SFM2 has options for Pressure and Temperature/Humidty sensors. The SFM2 provides ultra low drift, ultra low-power, and easy configuration. The SFM2 provides up to 833Hz Sensor Fusion output data rate. SFM2's In Stock Now!! Updated with USB-C Connector!! COMING SOON => Streaming Audio from SFM2 to the Mobile App!! INQUIRE FOR VOLUME PRICING -
Sensor Maestros is the original inventor of the Rapid Prototyping Platform. Loads of thought and planning was put into the design of the smWSP-ARD. The smWSP-ARD is a Rapid Prototyping Platform for BLE and Sensor development. The smWSP-ARD has been designed to precisely mate with the Nordic nRF52 DK and is compatible with Ardiuno Revision 3. It can be used as a shield with Arduino Revision 3 compatible boards such as the nRF52 DK or as a Stand-alone BLE Sensor development kit with the addition of the smRF-LR832 Long Range modules based on the nRF52832 that provide up to +21dBm output power. For orders over 100 fill out this form. -
The ICS-43434 is a digital I2S output microphone featuring a bottom sound port. The ICS-43434 provides a direct Audio to Digital solution. No Audio Codec is needed to get direct sampled audio straight to a host processor. The ICS-43434 follows the industry standard 24-bit I2S interface for easy connection to any host processor that has an I2S interface. It provides 3 operation modes: High Performance(~490uA), Low Power(230uA) and Sleep(~12uA) while being powered from a 1.8V source. In a very small package size of 3.5x2.65x0.98mm it also provides a high SNR of 64dBA across a 20KHz bandwidth along with an exceptional Dynamic Range of 90dB. For orders over 35 fill out this form. -
The Silicon Labs Si7006-A20 is an I2C interface, ultra-small, Temperature and Humidity Combination IC. It is offered in a 3x3x0.75mm DFN-6 package. The Si7006-A20 provides 0-90% RH with an Accuracy of +5% (max). It is operational from 0-100% RH. The Humidity sensor is configurable from 8-12bits with conversion times from 2.6-10ms respectively. The SI7006-A20 incorporates a ‘heater’ element to aid in testing the sensor, to dry the sensor membrane, or to implement a dew-point. For orders over 100 fill out this form. -
The smMOTN-MMA8652 is a 3-Axis Accelerometer MMA8652 breakoutboard. The MMA8652 is an ultra-small 3-Axis, 12-bit I2C Accelerometer. It comes in a 2x2mm 10pin DFN package. It is one of the most cost-effective 3-Axis accelerometers on the market and is loaded with features. It is operational from 1.95-3.6V and the I2C interface can operate from a separate 1.62-3.6V if desired. It features ultra-low power consumption in which it can operate at 6.5uA in its lowest power settings. It features ±2, ±4, and ±8g dynamically selectable full-scale ranges. Output Data Rates range from 1.56-800Hz and provides a 12-bit I2C output. It features 2 programmable interrupts that can be connected to an external MCU. It features 4 channels of configurable motion detection(FreeFall, Motion, Pulse, and Transient). It provides orientation detection(Potrait/Landscape) with programmable hysteresis. To assist with ultra-low power operation it provides configurable automatic ODR changed triggered by the Auto-Wake/Sleep state change. It also features a 32-sample FIFO and a Self-Test feature. The smMOTN-MMA8652 provides an easy to use, low-cost, very small breakoutboard for the MMA8652. All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread-board or to be ‘wired’ into an application. The header-header spacing is 7.62mm (300mil). All SMSTRS smMEM, smSENSR, smCOM, smBAT, smPWR products are compatible with the Sensor Maestros Wireless Sensor Platforms that provide Rapid prototyping for Sensor and BTLE applications. The smMOTN-MMA8652 can be plugged into the smBLOCK I2C sockets in the smWSP and smWSP-ARD rapid prototyping sensor plugin boards. For orders over 100 fill out this form.