- 1600mAh Lithium Battery 50(W) x 48(L) x 6.0(H)mm
- Includes JST PHR-2 Connector - Commonly used for Drone Battery and RC products
- OV/UV Protection
- CE Certified!! CE Certification Document
- Ideal for Drone or Remote Control device battery replacement!!
-
INQUIRE FOR VOLUME ORDERS OR OTHER BATTERY SIZES/CAPACITIES!! 3 PIECE MINIMUM ORDER Sensor Maestros specializes in ultra low power product design. Inquire below for custom design services. Design Services Inquiry -
The AT45DB081E is a low voltage, low power Serial Flash Device. It boasts 400nA Ultra Deep Power Down currents. The device operates from 1.7V-3.6V and up to 85MHz with a Low Power Read at 15MHz. The AT45DB081E has a flexible erase architecture and can be erased by Page(256bytes), Block(2KB), Sector(64KB), or a full chip erase. The device also offers flexible Writes in which it can be programmed either by Bytes or by Page(256bytes) and has Dual-Input Byte/Page Program capability along with Sequential Program Mode capability. The AT45DB081E offers package options including 8ld SOIC(0.150” and 0.208” wide) and an 8ld UDFN(5x6x0.6mm) package of which the smMEM-AT45DB081 breakout board makes use of. Sensor Maestros developed Software API Library for the Adesto Technology Serial Flash IC's. The API library is a portable embedded 'C' abstraction layer that can be ported to any MCU platform and includes high level API's for everything from reading, writing, erasing, reading the device ID, etc. The API library is utilized in an Application Example using the Silicon Labs EFM32 MCU platform. This application software can be used with any of the Silicon Labs EFM32 or EFR32 Starter Kits and the smWSP(Rapid Prototyping Plugin Board). The smWSP plugs into any EFM32/EFR32 Starter Kit via the Expansion Port and allows all the Sensor Maestros smMEM, smSENSR, smMOTN, etc breakout boards to be plugged into the smBLOCKs(header blocks) on the smWSP. The EFM32 'C' demo firmware reads the smMEM device plugged into the smWSP and allow various functions to be performed such as Read, Write, Erase, etc and the power consumption can be easily measured using the Silicon Labs Energy Profiler. For orders over 100 fill out this form. -
The PAM8904 is a 1X/2X/3X Piezo Driver capabable of 1X/2X/3X Boost modes with an input of 1.8-5.5V. The smPWR-PAM8904 provides a micro-sized breakout board measuring 20.4x12.7mm for the PAM8904 and provides jumper pin selections for the 1X/2X/3X modes and oversized solder pads for connecting a piezo speaker/buzzer. Additionally the device has excellent built in features such as Automatic Standby Operation and Wake-Up-Control. Use the Open Source BLE Controllable Firmware and Flutter App to test the smPWM-PAM8904. nRF52/nRF52840 DK BLE Firmware: smPWM_BLE_nRF52 Firmware Flutter App controls DUTY_CYCLE and FREQUENCY: smPWM_BLE-Flutter -
The smACCEL-H3LIS331DL breakout board features the H3LIS331DL 400G 3-Axis Accelerometer on a micro-sized 12.7x15.2mm breakout board. The H3LIS331DL high-g accelerometer can be configured for 100G, 200G, or 400G Full Scale operation. It can be configured for a SPI or I2C interface. Sensor Maestros has expertise in precision motion tracking. We have developed numerous products in this area including the Wearable Precision 9 DOF IMU SFM2 and additionally the FAZR PUCK a first of its kind hockey puck that measures shot speed and provides user feedback via built-in LED's. We have also developed a LAX ball using the same technology. Let us know what we can develop for you or if you have interest in licensing our technology. DESIGN SERVICES INQUIRY -
Sensor Maestros developed the smMOTN-10 DOF-ST-LSM6DSO IMU Breakout Board to provide 9 DOF IMU capability. We also included a LPS22HH pressure sensor. Equally important we designed it to measure a mere 15.2mm x 12.7mm . The LSM6DSO utilizes a single SPI interface and directly interfaces to the LIS2MDL 3-Axis Magnetometer and LPS22HH pressure sensor. Sensor Maestros also designed this breakout board to be compatible with the smWSP-ARD and smWSP Rapid Prototyping Platforms. We developed these boards as Arduino and SiLabs EFR32 and EFM32 STK compatible.- LSM6DSO(3-Axis Accel & Gyro), LIS2DML(3-Axis Mag), LPS22HH(260-1260 Pressure Sensor)
-
Sensor Maestros developed the smMOTN-10 DOF-ST-LSM6DSV32 IMU Breakout Board to provide 9 DOF IMU capability. We also included a LPS22HH pressure sensor. Equally important we designed it to measure a mere 15.2mm x 12.7mm . The LSM6DSV32 utilizes a single SPI interface and directly interfaces to the LIS2MDL 3-Axis Magnetometer and LPS22HH pressure sensor. Sensor Maestros also designed this breakout board to be compatible with the smWSP-ARD and smWSP Rapid Prototyping Platforms. We developed these boards as Arduino and SiLabs EFR32 and EFM32 STK compatible.
- LSM6DSV32(3-Axis Accel & Gyro), LIS2DML(3-Axis Mag), LPS22HH(260-1260 Pressure Sensor)
-
smWSP-ARP: Wireless Sensor Rapid Prototyping Shield
The smWSP-ARD is a wireless sensor rapid prototyping shield that is Arduino R3 compatible. The smWSP-ARD supports all Sensor Maestros smMEM, smSENSR, smMOTN, smCOM, smBAT, and smPWR standardized pinout breakout boards. These breakout boards plug directly into the smWSP-ARD using smBLOCKs allowing you to rapidly prototype your wireless sensor hardware one day and completely change it the next day. Gone are the days of having to work with a sensor evaluation board that has several sensors you would love to change but they are soldered directly to the PCB. Now you can pick and choose your RF, sensor, memory, power, and battery configuration. Secondarily all these components can then be un-plugged from the smWSP-ARD to be either used in a prototype of your own, in a bread-board application, or simply be replaced by a different smBLOCK compatible component. smWSP-ARD Board Includes: smCOM(USB-UART) and the smWSP-ARD base board.IAQ-LOGR Open Source Wireless Indoor Air Quality Data Logger Application
The IAQ-LOGR is an Open-Source firmware application that implements a Wireless Indoor Air Quality Monitor and Data Logger using the smWSP-ARD base board. The IAQ-LOGR application utilizes the smSENSR, smMEM, and/or smPWR and smRF standardized plugins. The IAQ-LOGR reads and data logs CO2, Temperature, Humidity, and Ambient light using the following breakout boards listed below. Open Source IAQ-LOGR firmware Repository: IAQ-LOGR Firmware More information on the IAQ-LOGR at the following link: IAQ-LOGR Product Page Volume orders please inquire directly. -
This is a MP2148 Low Iq DC-DC Buck regulator breakout board. The Monolithic Power MP2148 is a DC/DC buck regulator capable of 1A continuous output current from a 2.3V-to-5.5V input voltage with excellent load and line regulation. All of this is achieved at a mere 11uA of quiescent current. Fault protections include cycle-by-cycle current limiting and thermal shutdown. The MP2148 is available in an ultra-small QFN- 6 (1.0mmx1.5mm) package and requires a low value inductor of only 1uH and can provide >90% efficiency. The smPWR-MP2148-ADJ provides an easy to use breakout board for the MP2148 measuring only 7.8x9.9mm. All pins are all mapped to standard 2.54mm/0.1” headers. This allows for use in a standard bread-board or to be ‘wired’ into an application. The header-header spacing is 7.62mm (300mil). The smPWR-MP2148-ADJ comes pre-configured for a 3.0V output but can be modified to provide a 1.8V output by simply moving R3(0603) 0ohm jumper. By default the EN line is pulled to Vin via R1(0ohm jumper). For external control for Enable/Disable simply remove R1. All SMSTRS smMEM, smSENSR, smCOM, smBAT, smPWR products are compatible with the Sensor Maestros Wireless Sensor Platforms that provide Rapid prototyping for Sensor and BTLE applications. The smPWR-MP2148-ADJ can be plugged into ANY of the smPWR sockets in the smRF-WB and smWSP-ARD rapid prototyping sensor plugin boards. smWSP-ARD: Arduino compatible IoT Sensor Rapid Prototyping Platform MP2148 Datasheet For orders over 100 fill out this form
